Welcome to Perry Impex +22 28205026

marketing@perryimpex.in

SINGLE PART SMOOTH & STRONG

BLOCKFIX MORTAR

DESCRIPTION :

PERRY BLOCLK FIX is a versatile thin jointing material for laying AAC blocks, fly ash bricks, concrete locks etc. PERRY BLOCLK FIX mortar is specially designed to provide stronger, much  more durable bonding between the blocks with superior adhesive strength. It replaces  conventional cement and sand mix mortar of

12-18 mm thickness with highly versatile  3-5 mm thickness.

USES :

Laying and jointing of masonry units like fly ash bricks, concrete blocks, hollow blocks , AAC blocks etc.

Jointing of pre-stressed concrete slabs, panels. Jointing of concrete window and door frames.  Garden and boundary walls.

ADVANTAGES : 

Fiber reinforced, crack resistant. No water curing is required after application, thus saving on labour & water required for curing the walls. Ready for subsequent application like plastering just after 24 hour application thus assuring speedy return on investment & saving on supervision &  labour cost & construction time of the project.

Instruction for use :

Surface Preparation

The surface of masonry units should be slightly wet prior  to application of PERRY BLOCLK FIX  Thesurface must be structurally sound. Effloresce & any other

contaminant which could impair the natural bond  should be removed. The masonry `units should be clean , with no loose particles or dust for better bonding. Surface defects such as cracks, holes or voids should be repaired prior to application.

Mixing :

Mixing Ratio – depending on the thickness of the product to be applied, add  approx.25- 30% of the clean potable water and 70% of powder and mix.

Water is added in stages to get a smooth, uniform, workable mix. Allow sample time

for initial mixing. Ensure that no powder is left unmixed at the bottom of the vessel.

Pre-mixed and ready to use. Only water to be added at site.

Compressive strength is 3-4 times higher than the

CONVENTIONAL MORTAR.

PROPERTIES :

Appearance : Free flow Grey powder Composition :Portland cement, selected sand, bonding additives.Water Demand : 25 – 30%

Work ability :Good

Hard Dry :24 hours @ 30°C

Wet mix life :1 hour at 30°C

Curing :It is self curing, No additional water curing is required Tensile Adhesion

Strength : 0.8 5 N / S q.mm @ 28 day

I Thinner jointing material with very high adhesive strength.Improves over all masonry strength and load bearing capacity & waterproofing properties. Thinner layer of application for lesser shrinkage and seamless structure.Eliminates lengthy process of site mixing, transport and storage of all individual materials.

PERRY BLOCK FIX

Application :

Layout the wall in which is to be used  and mark openings like doors, windows, any architectural appurtenances etc.

Put a thin layer of PERRY BLOCLK FIX in the thickness of 3 to 5mm on the clean and leveled surface using proper trowel on which the block work is to be carried out.

Place the block on the laid PERRY BLOCLK FIX in proper line and level. After placing the first block apply the PERRY BLOCLK FIX of same thickness on both the sides of the block continuously keeping a check on the line and level. Clean the excess material, if any immediately. Continue the procedure for the entire block work.

Tools and equipment can be easily cleaned with clean water.

PACKING & COVERAGE :

PERRY BLOCLK FIX is available in 40 kg. of HDPE laminated bags. Under  normal condition, the coverage of at average thickness of 2-3 mm for a bag of 40 kg. is PERRY BLOCLK FIX .

PERRY IMPEX

1st Floor, Prabhu Nivas,New Nagardas Road,Andheri (E) Mumbai -400 069

Tele :  28365024, 28365027

Mobile: 09820232195, 9892493249

Email:  perryimpex@yahoo.com

The information herein is based upon the best information available at the time of printing. Data provided is intended for those having skill and ability to use products recommended in a safe and responsible manner. Liability is limited to the cost of material proven to be defective. There is no warranty expressed or implied as related to any issue which is deemed to be a direct result of improper surface preparation

or cleaning, application over concrete or cementitious surfaces which have not reached full cure, those having excessive rising moisture/vapour or hydrostatic pressure, application over surface which have previously been sealed without first testing for compatibility/adhesion, adverse water condition, acts of God or acts of others, constant submersion in harsh environments, workmanship or applicator, or any

other cause and effect which is not related to defective material.

NON-WARRANTY

BLOCK / BRICK SIZE UNIT COVERAGE AREA

BLOCK /BRICK SIZE UNIT COVERAGE AREA
100mm×240mm×650 Sq.ft. 160-180
125mm×240mm×650 Sq.ft. 130-150
150mm×240mm×650 Sq.ft. 120-140
200mm×240mm×650 Sq.ft. 80-100

The coverage area however will depend upon the  quality & evenness of the substrate thickness of   joints and size of masonry units. For best results proper tools for mixing and application is advised which will result in higher coverage, savings in time and man power.

SHELF LIFE & STORAGE :

PERRY BLOCLK FIX has a shelf life of 6 months from date of manufacture when kept at a temperature between 5 0C to 45 0C and store in the original, unopened bags. All material shall be stored under cover in a manner that will prevent damage preferable on pallets and protected from excessive heat and moisture. Do not freeze. 

HEALTH & SAFETY :

PERRY BLOCLK FIX

skin, eyes or be swallowed.Protective glasses should  be worn during mixing and application.Should PERRY  BLOCLK FIX come into contact with skin, remove

before hardening by washing with soap and water. Should accidental eye contact occur wash with plenty of water and seek medical advice. If swallowed seek medical

advice immediately. Do not induce vomiting. For full health  and safety data refer to Product Safety Data Sheet.